
ServicesUV Water Purification
UV Water Purification in Niederwald
A UV system neutralizes 99.9% of bacteria in your water without adding chemicals or changing the taste. We test your water first, add any pretreatment it needs, and size the unit to your home's peak flow so every gallon gets a full dose.
What UV Does and When It Is the Right Call
A UV system is a sealed metal housing with a UV-C lamp running down its center, protected by a clear quartz sleeve. As your water passes that sleeve, light at 254 nanometers neutralizes 99.9% of bacteria such as E. coli, so they cannot multiply. The water picks up no chemicals and loses none of its minerals on the way through.
That last point matters. UV does not remove lead, nitrates, iron, chlorine, hardness or sediment, and it leaves no residual disinfectant in your pipes. It is the right call when a test shows coliform bacteria, when your home draws from a private well or cistern, or when you want a microbial safeguard behind a filter. If your concern is taste, odor or chemicals, a carbon system or reverse osmosis fits better, and we will tell you so.
Timing helps. Heavy spring and fall storms are when surface runoff is most likely to reach a shallow well or a cracked well cap, so we like to have UV running and a fresh lamp in place before that weather arrives.
What Our UV Installation Includes
- Sizing to your peak flow
- We count fixtures and estimate how many gallons per minute your home pulls when the shower, washer and a faucet run together. The unit is rated to deliver its full dose at that flow, not just at a trickle.
- Sediment prefilter
- A 5-micron sediment cartridge goes ahead of the UV chamber. Particles can shade microorganisms from the light, so clear water is a requirement, not an upgrade.
- Pretreatment where the test calls for it
- Iron above about 0.3 ppm, manganese or hardness above roughly 7 grains per gallon will coat the quartz sleeve and block the light. When your results show that, we pair UV with Iron and Sulfur Removal or a softener or conditioner ahead of it.
- Bypass valves and a dedicated outlet
- We plumb in a bypass so the unit can be serviced without shutting off your home's water. The ballast plugs into a protected outlet, and we confirm the alarm works if the lamp fails.
- Line disinfection after startup
- UV only treats water as it passes through. After installation we disinfect the plumbing downstream so bacteria already living in the lines are cleared out.
Signs Your Home Could Use UV Purification
A positive coliform result
Total coliform or E. coli on a lab report means something is getting into your water. UV handles the microbes while you look for the source.
Your water comes from a private well
No utility is disinfecting it for you. A cracked cap, a failing seal or nearby septic can introduce bacteria without any change in how the water looks.
Stomach trouble after storms
If upset stomachs seem to follow heavy rain, runoff may be reaching your supply. Test the water and do not wait for the next storm.
Cloudiness after rain
Water that turns hazy after a downpour is carrying sediment, and often the bacteria and parasites that travel with it.
An old UV unit nobody has serviced
A lamp keeps glowing long after its UV output has dropped below a safe dose. If yours has run more than a year on the same bulb, it is likely underperforming.
How the Job Runs
- 1
Free water test
We test for bacteria indicators, iron, manganese, hardness and clarity. Those numbers decide whether UV can work alone or needs pretreatment.
- 2
Plan and quote
You get a written quote that lists the UV unit, prefilter and any pretreatment line by line, with the reason for each part.
- 3
Installation day
We shut off the water, cut in at the main line after the pressure tank and before the water heater, and mount the equipment with bypass valves. Drop cloths go down, and we clean up the cut pipe and packaging before we leave.
- 4
Startup and handoff
We power the ballast, let the lamp warm up, flush and disinfect the lines, and show you the alarm, the lamp timer and how to change the prefilter.

What Moves the Price of a UV System
The UV unit itself is often the smaller part of the cost. Most of the quote comes down to what your water needs before it reaches the lamp and how much water your home moves at once. We offer free installation, so your quote is mainly the equipment your test shows you need.
- Flow rate
- Homes with more bathrooms pull more gallons per minute at the same moment. That calls for a chamber rated for higher flow and a more powerful lamp so the dose holds up at peak demand.
- Pretreatment
- Clear, low-mineral water may need only a sediment filter. Water with iron, manganese or hardness needs another system ahead of the UV.
- Plumbing layout
- Tight spaces, an awkward pressure tank location or pipe material that needs adapters adds parts and time.
- Monitoring features
- Basic units have a lamp-failure alarm. Some add a UV intensity sensor that warns you when output drops, which costs more but tells you more.
Common Questions About UV Systems
Something not covered here? (512) 710-1991
Does a UV system affect the flavor or odor of my water?
It does not. UV light passes through the water without altering its chemistry, so your water keeps the flavor and smell it has now. When the problem is a chlorine taste or a rotten-egg odor, carbon filtration or sulfur removal addresses it, and we can mount the UV unit downstream of that equipment.
How long does a UV lamp last before it needs replacing?
Plan on a new lamp every year, which works out to around 9,000 hours of running time. An old lamp keeps glowing, but its germicidal output drops below an effective dose. A lot of our customers swap it ahead of the spring storms so the bulb is at full strength when runoff risk peaks.
Should I leave the UV unit switched on all the time?
Yes, keep it running. The lamp needs a few minutes to warm up to full output, and frequent on-off cycling wears it out faster. Power use is close to that of a single household light bulb, so continuous operation adds very little to your bill.
What should I do after a power outage?
While the lamp is dark, water flows through the chamber untreated. Once the power is back, open your taps and let them run several minutes to flush that water out. After a long outage, or one that came with flooding, have the water tested before anyone drinks it.
Does the quartz sleeve need cleaning if I have pretreatment?
It does. Even with a prefilter or softener ahead of it, minerals build a thin film on the sleeve over time. Clean or descale it each time you replace the lamp, because a coated sleeve blocks the light just as a worn-out bulb would.

Get UV Running Before the Next Storm Season
We start with a test so the UV system matches your water and your flow. Pretreatment, sizing and line disinfection are all spelled out in your quote before any work begins.